• HP 250 G7 - nie włącza się

Forumsregeln:Die Forumsregeln lesen

  1. Der Titel des Themas sollte Folgendes enthalten: den Hersteller der Maschine, das vollständige Modell und die kurze Beschreibung des Fehlers.
  2. Die Themennachricht sollte enthalten: einen PCB-Markierungscode (im Falle von Hardware-Reparaturen), erweiterte Beschreibung des Fehlers, Was wurde überprüft/ersetzt/gemessen + Schlussfolgerungen und, die Frage. Wenn Sie keinen PCB-Markierungscode finden können, du solltest lesen DIESES THEMA. Wenn Sie immer noch keine PCB-Markierungscode finden können, laden Sie bitte ein sauberen Fotos von beiden Seiten des Motherboards - ist es erforderlich, alle Filme und Module zu entfernen, die möglicherweise diese Markierungen abdecken könnte.
  3. Bevor Sie ein neues Thema veröffentlichen, sollten Sie alle Themen im Unterforum AUSBILDUNGEN lesen und machen Sie eine vorläufige Diagnose basierend auf dem Inhalt dieser Ausbildungen.
  4. Das Hochladen vollständiger Anweisungen/Schaltpläne oder BIOS-Dateien / Firmware (oder das Verlinken auf andere Websites mit solchen Dateien) ist STRENG VERBOTEN. Sie können nur den kleinen Teil der Anweisung/Schaltplans oder den Link zur BIOS-Datei in UNVERIFIZIERTE BIOS-DATEIEN platzieren, der die Diagnose und Reparatur für den Themenautor vereinfacht. Sie können nicht mehr als eine vollständige Seite mit Anweisungen/Schaltplänen pro einzelnem Thema platzieren. Die Datei darf keine sichtbaren Wasserzeichen, "vertraulichen" Markierungen, E-Mail-Adressen usw. enthalten.
  5. Pro Thema darf nur eine fehlerhafte Maschine beschrieben werden. Für jede nächste Maschine sollten Sie ein neues Thema öffnen.
  6. Das Anfordern von Schaltplänen, Boardview, MB-Fotos, BIOS-Dateien oder Servicehandbüchern ist STRENG VERBOTEN. Wenn Sie irgendwelche von denen fragen wollen, sollten Sie ein neues Thema in DOKUMENTATION UND BIOS/EFI ANFRAGE Sub-Forum öffnen.

#1 HP 250 G7 - nie włącza się


von Snaeyk1980 2 Februar 2025, 13:01
Witajcie

Laptop HP 250 G7 - płyta GPI 52 LA-J952P

Po podłączeniu zasilania nie włącza się. Świeci dioda w gnieździe zasilania. Pomiary oporności na cewkach głównych przetwornic - brak zwarć.
Napięcie +3ALW - startuje na kilka sekund, później znika.
Napięcie +5ALW - startuje na kilka sekund, później znika.

Rozlutowałem zworę PJ305, aby wykluczyć przeciążenie gałęzi, taka sama reakcja. Napięcie +5ALWP startuje na kilka sekund.

Pomiary przetwornicy PU302:

+19VB_5V - obecne
+5VALWP - start na kilka sekund
+5VL - obecne
VCC_5V - obecne (jednak 3,3V)
SPOK - po podłączeniu zasilania w stanie niskim (0,27V), po kilku sekundach 0V
ENLDO_3V5V - stabilne 9,5V
5V_3V_EN - po włączeniu zasilania 3,1V, po kilku sekundach 0V
5V_FB - dopóki jest napięcie na PL301 wynosi 0,63V

Podobnie zachowuje się PU301
+19VB - obecne
3VALWP - startuje na kilka sekund
+3VLP - obecne
SPOK - 3,3V przez kilka sekund
ENLDO_3V5V - stabilne 9,5V
5V_3V_EN - po włączeniu zasilania 3,1V, po kilku sekundach 0V
3V_FB - dopóki jest napięcie na PL302 wynosi 0,63V

Po podłączeniu zasilania do momentu odcięcia przetwornic CPU startuje. Pobór na zasilaczu 0,2A, po kilku sekundach spadek do 0,03A, a po kolejnej sekundzie 0A.
Czy jest to uszkodzenie przetwornicy PU302. Brak przejścia SPOK w stan wysoki i odcięcie?

Re: HP 250 G7 - nie włącza się


von Google Adsense [BOT] 2 Februar 2025, 13:01

#2 Re: HP 250 G7 - nie włącza się


von matic 3 Februar 2025, 09:21
Hello!

Measure the resistance between pin 9 of chip PU301 and pin 9 of chip PU302.

#3 Re: HP 250 G7 - nie włącza się


von Snaeyk1980 3 Februar 2025, 09:30
PU301 - pin 9 - 130k
PU302 - pin 9 - open

#4 Re: HP 250 G7 - nie włącza się


von matic 3 Februar 2025, 09:47
You probably measured the resistances to ground, but I asked about one measurement directly between pins 9 of both chips (put one probe to the pin 9 of PU301 and another probe to the pin 9 of PU302).

#5 Re: HP 250 G7 - nie włącza się


von Snaeyk1980 4 Februar 2025, 07:54
OK, my foult. Resistance between pin 9 PU301 and pin 9 PU 302 still "open line".

#6 Re: HP 250 G7 - nie włącza się


von matic 4 Februar 2025, 08:11
Snaeyk1980 hat geschrieben:Czy jest to uszkodzenie przetwornicy PU302. Brak przejścia SPOK w stan wysoki i odcięcie?
So the chip PU302 is fine. The "SPOK" of this chip is not used in this case.

Reflash the BIOS chip. Don't forget to save the old dump.

#7 Re: HP 250 G7 - nie włącza się


von Snaeyk1980 4 Februar 2025, 10:31
I flashed the BIOS with a file from the HP repository. Now the PCH starts for two seconds, then I see on the thermal imaging that PU301 is heating up. After a few seconds it cuts off and PU301 starts pulsing. In the old BIOS, both PCH and CPU started working for a few seconds.

#8 Re: HP 250 G7 - nie włącza się


von matic 4 Februar 2025, 14:32
Try with another BIOS dump, best with a cleaned ME-region.

#9 Re: HP 250 G7 - nie włącza się


von Snaeyk1980 5 Februar 2025, 15:07
I tested on several bioses with the ME region cleared. Without changes. When the board is started, the hybrid bridge warms up slightly, then the voltages are cut off and the PU301 converter pulsates gently.

#10 Re: HP 250 G7 - nie włącza się


von matic 6 Februar 2025, 07:56
Measure the voltages to ground on all coils for a short time, while the machine is turned on (the APU hybrid is warming up).

#11 Re: HP 250 G7 - nie włącza się


von Snaeyk1980 6 Februar 2025, 09:20
PL301 - 5,1 V
PL302 - 3,39 V
PLB1 - 3,1 V - slowly growing. It does not disappear when the converters are cut off.
PLV3 - 0 V
PLV4 - 0 V
PLW1 - 0 V
PLZ1 - 0 V
PLZ2 - 0 V
PLG1 - 0 V

#12 Re: HP 250 G7 - nie włącza się


von matic 7 Februar 2025, 14:34
Snaeyk1980 hat geschrieben:When the board is started, the hybrid bridge warms up slightly
Are you sure that the APU hybrid is warming up?
The voltages on the coils do not indicate that.

#13 Re: HP 250 G7 - nie włącza się


von Snaeyk1980 7 Februar 2025, 15:21
I am posting a link to a video showing the board's reaction after power is applied.

https://youtu.be/7UlLcq4COn8

You can't see it well in the video, but the PU301 converter is pulsating.

#14 Re: HP 250 G7 - nie włącza się


von matic 9 Februar 2025, 21:32
Does the power consumption of the board change after pressing to the power button (maybe only for a short time)?
Specify the power consumption (in mA) of the board before and after pressing to the power button.

#15 Re: HP 250 G7 - nie włącza się


von Snaeyk1980 11 Februar 2025, 12:32
Current consumption after connecting the power supply is 40mA. After cutting off the converters it drops to 0mA. After pressing the POWER button the board draws 40mA, then the converters are cut off and the current consumption drops to 0mA.
Once in a while after pressing the POWER button the converters are not cut off, the board then draws 30 - 40mA, the bridge in the hybrid heats up slightly.
The measurements are not accurate, I read them from an external power supply.

#16 Re: HP 250 G7 - nie włącza się


von matic 2 März 2025, 12:52
The APU hybrid is probably damaged.
You can try to reflow it, but it needs to be replaced for the permanent repair.

Re: HP 250 G7 - nie włącza się


von Google Adsense [BOT] 2 März 2025, 12:52

Wer ist online?

Mitglieder in diesem Forum: 0 Mitglieder und 8 Gäste

_______________________________
Alle Rechte vorbehalten. Das unerlaubte Kopieren des Inhalts dieser Website oder eines Teils davon ist strengstens untersagt.
Alle auf dieser Website veröffentlichten Marken, Markennamen, Produkte oder Dienstleistungen gehören ihren gesetzlichen Eigentümern, sind urheberrechtlich geschützt und werden nur zu Informationszwecken verwendet.