• Laptop Acer Helios 300 PH317-52 - spalony

Forum rules:Click here to view the forum rules

  1. Topic title should contain: the device's manufacturer, full model and the brief description of problem.
  2. Topic message should contain: the PCB marking code (required in case of hardware repairs), an extended description of problem, things you have checked/replaced/measured, your conclusions and the question. If you are not able to find the PCB marking code, please read THIS TOPIC. If you still cannot locate the PCB markings, please upload a clean, both-side photos of the mainboard - it is required to remove any films, modules or brackets possibly covering these markings.
  3. Before posting a new topic please read all topics in TRAININGS subforum and make a preliminary diagnostic based on the content of those trainings.
  4. Uploading of any complete schematics, BIOS / firmware files or any other kind of documentation, or linking to 3rd party websites with such files, is STRICTLY PROHIBITED. You can only upload the small portion of documentation or, link to BIOS file on UNVERIFIED BIOS FILES subforum, which simplifies the diagnostics/repair. You are not allowed to upload more then one complete page of instruction/schematic per single topic. The file you upload must not contain any watermarks, "confidential" markings, links or email addresses and cannot be password-protected.
  5. It is only permitted to describe one faulty device per single topic - you should always open a new topic for each subsequent device.
  6. Requesting of the full schematics, BoardView files, BIOS files or any other kind of documentation is NOT ALLOWED in this subforum. If you need to ask for any of these, you should open a new topic in DOCUMENTATION/BIOS REQUEST subforum.
This topic is marked as ARCHIVAL. Please only reply if your message contains the solution (Terms and Conditions p. 12.1).

#1 Laptop Acer Helios 300 PH317-52 - spalony


by krzysztof000 3 February 2024, 02:18
Witam,

Model płyty LA-F991P nie włącza się, spalony element jak na zdjęciu PQ1701. Co to za układ? Jakiś mosfet? Czy można czymś zastąpić?

Image

Re: Laptop Acer Helios 300 PH317-52 - spalony


by Google Adsense [BOT] 3 February 2024, 02:18

#2 Re: Laptop Acer Helios 300 PH317-52 - spalony


by paij0 3 February 2024, 04:53
mosfet AON6992

#3 Re: Laptop Acer Helios 300 PH317-52 - spalony


by lukaszek32167 3 February 2024, 09:06
Cześć,
PQ1701=AON6962

#4 Re: Laptop Acer Helios 300 PH317-52 - spalony


by krzysztof000 3 February 2024, 10:45
I to musi być taki sam układ czy można jakiś zamiennik wlutować?

#5 Re: Laptop Acer Helios 300 PH317-52 - spalony


by Vogelek23 3 February 2024, 11:37
Można zastosować inny o zbliżonych parametrach. Tutaj masz instrukcję, jak szukać zamienników: post198619.html#p198619

#6 Re: Laptop Acer Helios 300 PH317-52 - spalony


by matic 3 February 2024, 12:13
That's a fairly common fault on these boards.
First of all remove the burned PQ1701 (or whatever is left of him) from the board and check the condition of the PCB itself on the place of this transistor. Be careful not to cause additional damage when removing the transistor as it seems to be burned to the point where it could be welded to board itself due to severe overheating. In such a case it's best to grind it off the board using a Dremel.

The damage on this transistor may lead to the VRAM chips or/and the GPU chip failure.
However, remove the burned transistor from the board first, check the PCB itself on the place of this transistor and measure the resistance to ground on coil PL1701.

#7 Re: Laptop Acer Helios 300 PH317-52 - spalony


by krzysztof000 20 February 2024, 00:43
Strasznie to jest wypalone.
Jak to dokładnie oczyścić bo jest bałagan.
Załaczam zdjęcia:

Image

Image

Teraz rezystancja na cewce PL1701 = 010,07Ω
A na cewce PL1702 = 010,11Ω do masy.

#8 Re: Laptop Acer Helios 300 PH317-52 - spalony


by matic 20 February 2024, 07:54
krzysztof000 wrote:rezystancja na cewce PL1701 = 010,07Ω
What does it mean? Do you mean 10.07Ω or what?
If so, this resistance is too low. Remove the capacitors PC1710, PC1722 from the board and remeasure the resistance to ground on coil PL1701.

This topic is marked as ARCHIVAL. Please only reply if your message contains the solution (Terms and Conditions p. 12.1).

Who is online

Users browsing this forum: No registered users and 1 guest

_______________________________
All rights reserved. Unauthorised copying of this website's content or any of its part is strictly forbidden.
Any trademarks, brand names, products or services published on this website belong to their legal owners, are copyrighted and used for information purposes only.