• Lenovo flex 14 no display short, da0st6mb6e0 Rev :E

Forumsregeln:Die Forumsregeln lesen

  1. Der Titel des Themas sollte Folgendes enthalten: den Hersteller der Maschine, das vollständige Modell und die kurze Beschreibung des Fehlers.
  2. Die Themennachricht sollte enthalten: einen PCB-Markierungscode (im Falle von Hardware-Reparaturen), erweiterte Beschreibung des Fehlers, Was wurde überprüft/ersetzt/gemessen + Schlussfolgerungen und, die Frage. Wenn Sie keinen PCB-Markierungscode finden können, du solltest lesen DIESES THEMA. Wenn Sie immer noch keine PCB-Markierungscode finden können, laden Sie bitte ein sauberen Fotos von beiden Seiten des Motherboards - ist es erforderlich, alle Filme und Module zu entfernen, die möglicherweise diese Markierungen abdecken könnte.
  3. Bevor Sie ein neues Thema veröffentlichen, sollten Sie alle Themen im Unterforum AUSBILDUNGEN lesen und machen Sie eine vorläufige Diagnose basierend auf dem Inhalt dieser Ausbildungen.
  4. Das Hochladen vollständiger Anweisungen/Schaltpläne oder BIOS-Dateien / Firmware (oder das Verlinken auf andere Websites mit solchen Dateien) ist STRENG VERBOTEN. Sie können nur den kleinen Teil der Anweisung/Schaltplans oder den Link zur BIOS-Datei in UNVERIFIZIERTE BIOS-DATEIEN platzieren, der die Diagnose und Reparatur für den Themenautor vereinfacht. Sie können nicht mehr als eine vollständige Seite mit Anweisungen/Schaltplänen pro einzelnem Thema platzieren. Die Datei darf keine sichtbaren Wasserzeichen, "vertraulichen" Markierungen, E-Mail-Adressen usw. enthalten.
  5. Pro Thema darf nur eine fehlerhafte Maschine beschrieben werden. Für jede nächste Maschine sollten Sie ein neues Thema öffnen.
  6. Das Anfordern von Schaltplänen, Boardview, MB-Fotos, BIOS-Dateien oder Servicehandbüchern ist STRENG VERBOTEN. Wenn Sie irgendwelche von denen fragen wollen, sollten Sie ein neues Thema in DOKUMENTATION UND BIOS/EFI ANFRAGE Sub-Forum öffnen.
Dieses Thema ist als ARCHIV markiert. Antworten Sie nur, wenn Ihre Nachricht eine Lösung enthält (Allgemeine Geschäftsbedingungen, 12.1)

#1 Lenovo flex 14 no display short, da0st6mb6e0 Rev :E


von Codetrr 21 Juni 2024, 07:58
Previously when the laptop was turned on it responded and the power light came on but then turned off.

1. With lesson 7 it turns out to be short in PL8, PL4, PL3.
2. I checked the PL8 line, it turned out C291 was burnt.
then I took it off and tried to turn it on . it turned on with the fan spinning (maybe it was already booted) (with new ram ok, with old ram won't turn on).

The problem is PL4, PL3 are still short and now the LCD is just dark, there is no display. I tried disconnecting PL3 and PL4 but there was a short in VGPU_CORE.

How do I check the short section with lots of capacitors going to VGPU_CORE? And does capacitor C291 need to be replaced? or just let it go?

Re: Lenovo flex 14 no display short, da0st6mb6e0 Rev :E


von Google Adsense [BOT] 21 Juni 2024, 07:58

#2 Re: Lenovo flex 14 no display short, da0st6mb6e0 Rev :E


von Vogelek23 21 Juni 2024, 10:44
Codetrr hat geschrieben:PL4, PL3 are still short
At GPU power path you should expect very low resistance to ground, even below 1Ω, depending on GPU chip model. What is the actual resistance on PL3/4 to ground (measured at Ω lowest scale, not at diode scale)? Please take into consideration the resistance of your probe cables. And what is the marking on GPU chip?

Codetrr hat geschrieben:How do I check the short section with lots of capacitors going to VGPU_CORE?
The answer is: SHORT TEST. Please read Lesson 3 carefully: post5699.html#p5699

#3 Re: Lenovo flex 14 no display short, da0st6mb6e0 Rev :E


von Codetrr 21 Juni 2024, 15:31
pl3/4
Resistance is 39 ohm
Voltage is 0.905 volt

Marking on GPU is N14m- GE-A2
Is it safe to leave c291, because I don't have changer for this capasitor.

#4 Re: Lenovo flex 14 no display short, da0st6mb6e0 Rev :E


von Vogelek23 21 Juni 2024, 16:05
Codetrr hat geschrieben:pl3/4
Resistance is 39 ohm
Voltage is 0.905 volt
So it seems it is all good here.

Codetrr hat geschrieben:Is it safe to leave c291
It should be okay with just the one capacitor missing on that power path.

Measure the voltages to ground on pins 1, 8, 9, 28 and 30 of CN3 connector when the logic board is turned on. Best would be to disconnect the battery and HDD/SSD before taking measurements (just the power supply and screen connected).

#5 Re: Lenovo flex 14 no display short, da0st6mb6e0 Rev :E


von Codetrr 21 Juni 2024, 17:24
Cn3:
1. 20.5v
8. 370 mV
9. 470 mV
28. 3.28 V
30. 0 V

After I check on schematic and board, U1 not present on board.

Bild

Bild

#6 Re: Lenovo flex 14 no display short, da0st6mb6e0 Rev :E


von Vogelek23 21 Juni 2024, 20:05
Codetrr hat geschrieben:U1 not present on board
Correct, +LCDVCC voltage comes from U7 (RTD2132R) pin 15 via R13 jumper. Check if you have any picture on external HDMI monitor while the internal LCD panel is disconnected from the logic board. Do not forget to disconnect all the power before you disconnect or connect the LCD panel's cable.

#7 Re: Lenovo flex 14 no display short, da0st6mb6e0 Rev :E


von Codetrr 22 Juni 2024, 05:30
I tried with external HDMI monitor but nothing is displayed.
After waiting 3 hours the CPU fan is still on.
Pl3 and pl4 little bit warmer than other PL.
What else should I check?

Re: Lenovo flex 14 no display short, da0st6mb6e0 Rev :E


von Google Adsense [BOT] 22 Juni 2024, 05:30
Dieses Thema ist als ARCHIV markiert. Antworten Sie nur, wenn Ihre Nachricht eine Lösung enthält (Allgemeine Geschäftsbedingungen, 12.1)

Wer ist online?

Mitglieder in diesem Forum: 0 Mitglieder und 9 Gäste

_______________________________
Alle Rechte vorbehalten. Das unerlaubte Kopieren des Inhalts dieser Website oder eines Teils davon ist strengstens untersagt.
Alle auf dieser Website veröffentlichten Marken, Markennamen, Produkte oder Dienstleistungen gehören ihren gesetzlichen Eigentümern, sind urheberrechtlich geschützt und werden nur zu Informationszwecken verwendet.