• Lenovo P51 płyta DP510 NM-B041 nie rozpoznaje zasilacza

Forum rules:Click here to view the forum rules

  1. Topic title should contain: the device's manufacturer, full model and the brief description of problem.
  2. Topic message should contain: the PCB marking code (required in case of hardware repairs), an extended description of problem, things you have checked/replaced/measured, your conclusions and the question. If you are not able to find the PCB marking code, please read THIS TOPIC. If you still cannot locate the PCB markings, please upload a clean, both-side photos of the mainboard - it is required to remove any films, modules or brackets possibly covering these markings.
  3. Before posting a new topic please read all topics in TRAININGS subforum and make a preliminary diagnostic based on the content of those trainings.
  4. Uploading of any complete schematics, BIOS / firmware files or any other kind of documentation, or linking to 3rd party websites with such files, is STRICTLY PROHIBITED. You can only upload the small portion of documentation or, link to BIOS file on UNVERIFIED BIOS FILES subforum, which simplifies the diagnostics/repair. You are not allowed to upload more then one complete page of instruction/schematic per single topic. The file you upload must not contain any watermarks, "confidential" markings, links or email addresses and cannot be password-protected.
  5. It is only permitted to describe one faulty device per single topic - you should always open a new topic for each subsequent device.
  6. Requesting of the full schematics, BoardView files, BIOS files or any other kind of documentation is NOT ALLOWED in this subforum. If you need to ask for any of these, you should open a new topic in DOCUMENTATION/BIOS REQUEST subforum.
This topic is marked as ARCHIVAL. Please only reply if your message contains the solution (Terms and Conditions p. 12.1).

#1 Lenovo P51 płyta DP510 NM-B041 nie rozpoznaje zasilacza


by dggn 15 December 2023, 13:45
jak w temacie po włączeniu laptopa komunikat AC Adapter Unknow

z pomiarów napięć
PD26 2.4V
PQ40
n.1 2.4V
n.2 9.7V
n.3 2.4V

PQ41
n.1 2.4V
n.2 9.7V
n.3 2.4V

z pomiarów rezystancji do masy
PD26 po za zakresem
PQ40
n.1 ok. 2.5MΩ
n.2 0.64MΩ
n.3 0.75MΩ

PQ41
n.1 4.30kΩ
n.2 0.64MΩ
n.3 0.81MΩ

Rezystancja między n.1 układów PQ40 i PQ41 8.1MΩ

Co mogę jeszcze sprawdzić i czy to są prawidłowe parametry. Z góry dziękuję

Re: Lenovo P51 płyta DP510 NM-B041 nie rozpoznaje zasilacza


by Google Adsense [BOT] 15 December 2023, 13:45

#2 Re: Lenovo P51 płyta DP510 NM-B041 nie rozpoznaje zasilacza


by matic 15 December 2023, 13:53
Hello!

Measure the voltages to ground on both pins of resistor R412.

#3 Re: Lenovo P51 płyta DP510 NM-B041 nie rozpoznaje zasilacza


by dggn 18 December 2023, 14:56
napięcia rezystora R412
n.1 2.43V ( od strony R399)
n.2 2.45V

#4 Re: Lenovo P51 płyta DP510 NM-B041 nie rozpoznaje zasilacza


by matic 19 December 2023, 08:00
Reflash the KBC chip U27 with programmer. If it doesn't change anything, replace it.

#5 Re: Lenovo P51 płyta DP510 NM-B041 nie rozpoznaje zasilacza


by dggn 5 January 2024, 14:03
U27 to MEC1653-BA1. Podpowie ktoś jak tą płytę przygotować do programowania tego układu ?

#6 Re: Lenovo P51 płyta DP510 NM-B041 nie rozpoznaje zasilacza


by matic 6 January 2024, 19:14
Which programmer do you have?

#7 Re: Lenovo P51 płyta DP510 NM-B041 nie rozpoznaje zasilacza


by dggn 9 January 2024, 11:05
SVOD 4

poniżej zdjęcie okolicy układu U27
Image

#8 Re: Lenovo P51 płyta DP510 NM-B041 nie rozpoznaje zasilacza


by dggn 11 January 2024, 13:45
pomoże ktoś ogarnąć ?

#9 Re: Lenovo P51 płyta DP510 NM-B041 nie rozpoznaje zasilacza


by matic 12 January 2024, 12:59
Solder the following components to the board:
- Resistors R600, R601, R602, R603 (all are 0Ω (jumpers), package 0201).
- Resistors R604, R605, R606, R607 (all are 10kΩ/5%, package 0201).
- Switch the resistor R435 to the position of R434.
- Open the jumper PJ3.

- Connect the SVOD4 programmer to the connector JTAG1:
JTAG1 pin 1 -> TMS
JTAG1 pin 2 -> TDI
JTAG1 pin 3 -> TDO
JTAG1 pin 4 -> CLK
JTAG1 pin 5 -> GND

- Plug the power supply to the board.
- Inject 3.3V from the laboratory power supply to the pin 6 of connector JTAG1.

Re: Lenovo P51 płyta DP510 NM-B041 nie rozpoznaje zasilacza


by Google Adsense [BOT] 12 January 2024, 12:59
This topic is marked as ARCHIVAL. Please only reply if your message contains the solution (Terms and Conditions p. 12.1).

Who is online

Users browsing this forum: No registered users and 1 guest

_______________________________
All rights reserved. Unauthorised copying of this website's content or any of its part is strictly forbidden.
Any trademarks, brand names, products or services published on this website belong to their legal owners, are copyrighted and used for information purposes only.