plenrusldeituk
  • MSI GF63 MS-16R61 - Brak obrazu na LCD, HDMI działa

Forumsregeln:Die Forumsregeln lesen

  1. Der Titel des Themas sollte Folgendes enthalten: den Hersteller der Maschine, das vollständige Modell und die kurze Beschreibung des Fehlers.
  2. Die Themennachricht sollte enthalten: einen PCB-Markierungscode (im Falle von Hardware-Reparaturen), erweiterte Beschreibung des Fehlers, Was wurde überprüft/ersetzt/gemessen + Schlussfolgerungen und, die Frage. Wenn Sie keinen PCB-Markierungscode finden können, du solltest lesen DIESES THEMA. Wenn Sie immer noch keine PCB-Markierungscode finden können, laden Sie bitte ein sauberen Fotos von beiden Seiten des Motherboards - ist es erforderlich, alle Filme und Module zu entfernen, die möglicherweise diese Markierungen abdecken könnte.
  3. Bevor Sie ein neues Thema veröffentlichen, sollten Sie alle Themen im Unterforum AUSBILDUNGEN lesen und machen Sie eine vorläufige Diagnose basierend auf dem Inhalt dieser Ausbildungen.
  4. Das Hochladen vollständiger Anweisungen/Schaltpläne oder BIOS-Dateien / Firmware (oder das Verlinken auf andere Websites mit solchen Dateien) ist STRENG VERBOTEN. Sie können nur den kleinen Teil der Anweisung/Schaltplans oder den Link zur BIOS-Datei in UNVERIFIZIERTE BIOS-DATEIEN platzieren, der die Diagnose und Reparatur für den Themenautor vereinfacht. Sie können nicht mehr als eine vollständige Seite mit Anweisungen/Schaltplänen pro einzelnem Thema platzieren. Die Datei darf keine sichtbaren Wasserzeichen, "vertraulichen" Markierungen, E-Mail-Adressen usw. enthalten.
  5. Pro Thema darf nur eine fehlerhafte Maschine beschrieben werden. Für jede nächste Maschine sollten Sie ein neues Thema öffnen.
  6. Das Anfordern von Schaltplänen, Boardview, MB-Fotos, BIOS-Dateien oder Servicehandbüchern ist STRENG VERBOTEN. Wenn Sie irgendwelche von denen fragen wollen, sollten Sie ein neues Thema in DOKUMENTATION UND BIOS/EFI ANFRAGE Sub-Forum öffnen.

#1 MSI GF63 MS-16R61 - Brak obrazu na LCD, HDMI działa


von martiv 14 März 2025, 12:47
Witam,

Laptop MSI GF63 płyta główna: MS-16R61 - objaw: nie wyświetla obrazu na LCD, na zewnętrznym po HDMI obraz działa prawidłowo. Trafił do mnie po zalaniu, na płycie nie było śladów zalania - klawiatura musiała wszystko zatrzymać albo nie było dużej ilości cieczy.

Sprawdziłem złącze EDP 40 pin, najważniejsze pomiary z tego złącza, chyba że coś przeoczyłem.

3pin = 012V,
5pin = 1.75V,
6 pin = 5V,
7 PIN = 3.3V
32 PIN = 2.2V
33 - 36 PIN = 3.3V
38 - 40PIN - 19V

Pomiar układu PU21 MP2143 przełącznika 3.3V:

1 - 5V
2 - 5V
3 - 3.3V
4 - 0V
5 - 3.3V
6 - 0V
7 - 0.6V
8 - 3.3

Podmieniłem również na inną matrycę LCD - brak obrazu a nawet podświetlenia, co prawda nie miałem wersji 144hz ale FHD ze złączem edp 40PIN.
Nie mogę namierzyć schematu do tego modelu.

Co mogę jeszcze sprawdzić, zmierzyć w tym modelu ?
Będę wdzięczny za wskazówki.

Re: MSI GF63 MS-16R61 - Brak obrazu na LCD, HDMI działa


von Google Adsense [BOT] 14 März 2025, 12:47

#2 Re: MSI GF63 MS-16W21 - Brak obrazu na LCD, HDMI działa


von matic 16 März 2025, 13:55
Hello!

- Set your multimeter to the diode test mode and measure the voltage drops to ground on pins 3, 4, 8, 9, 11, 14, 15, 32 of LVDS connector EDP1 with the positive (red) probe connected to ground. Measure with the internal matrix disconnected from the board.

Perform the following measurements, when the machine is turned on with the external monitor disconnected from the board:
- Measure the voltage to ground on pin 32 of LVDS connector EDP1 with the internal matrix connected and disconnected from the board.
- Measure the voltages to ground on pins 14, 15 of LVDS connector EDP1 with the internal matrix connected to the board.

#3 Re: MSI GF63 MS-16W21 - Brak obrazu na LCD, HDMI działa


von martiv 17 März 2025, 13:11
internal matrix disconnected:

EDP PIN voltage drops:
3 - 0,44V
4 - 0V
8 - 0.75V
9 - 0V
11 - 0V
14 - 0V
15 - 0V
32 - 0.42V

matrix connected and disconnected PIN 32 = 0V
matrix connected PIN 14-15 = 0V

I understand that the edp_hdp PIN32 EDP LVDS signal comes from the PCH bridge?

#4 Re: MSI GF63 MS-16W21 - Brak obrazu na LCD, HDMI działa


von matic 18 März 2025, 09:33
Measure the resistances to ground on pins 3, 4, 8, 9, 11, 14, 15, 32 of LVDS connector EDP1 with the internal matrix disconnected from the board.

#5 Re: MSI GF63 MS-16W21 - Brak obrazu na LCD, HDMI działa


von martiv 18 März 2025, 11:27
matic hat geschrieben:Measure the resistances to ground on pins 3, 4, 8, 9, 11, 14, 15, 32 of LVDS connector EDP1 with the internal matrix disconnected from the board.


EDP connector:

PIN3 = 7.6kΩ
PIN4 = 7.6kΩ
PIN8 = 40kΩ
PIN9 = 40kΩ
PIN11= 0.66MΩ
PIN14 = 49.2kΩ
PIN15 = 0.586MΩ
PIN32 = 26.4kΩ

#6 Re: MSI GF63 MS-16W21 - Brak obrazu na LCD, HDMI działa


von martiv 24 März 2025, 10:15
on Pin 32 3.3V appears for a moment and then drops to 0V. with or without the matrix connected.

#7 Re: MSI GF63 MS-16W21 - Brak obrazu na LCD, HDMI działa


von matic 24 März 2025, 10:48
Please specify the model of the original matrix and the replacement one you tested with.

#8 Re: MSI GF63 MS-16W21 - Brak obrazu na LCD, HDMI działa


von martiv 24 März 2025, 12:02
Oryginal LCD: B156HAN15.1
Test LCD: B156HAN08.4

#9 Re: MSI GF63 MS-16W21 - Brak obrazu na LCD, HDMI działa


von matic 24 März 2025, 13:41
If you have an option, test the original matrix on any other laptop.

#10 Re: MSI GF63 MS-16W21 - Brak obrazu na LCD, HDMI działa


von martiv 26 März 2025, 14:51
I had no way to test the matrix on another laptop, I ordered a new original one for MSI. The effect is the same, no image. The voltage +3V_LCD appears for a moment and drops to 0V :frustry:

#11 Re: MSI GF63 MS-16W21 - Brak obrazu na LCD, HDMI działa


von matic 31 März 2025, 13:35
Something strange is going on with your measurements. You have measured voltage drops to ground of 0V (indicating a short circuit) on some pins of the LVDS connector, but at the same time the resistances on these pins are high:
martiv hat geschrieben:EDP PIN voltage drops:
4 - 0V
9 - 0V
11 - 0V
14 - 0V
15 - 0V
martiv hat geschrieben:EDP connector:
PIN4 = 7.6kΩ
PIN9 = 40kΩ
PIN11= 0.66MΩ
PIN14 = 49.2kΩ
PIN15 = 0.586MΩ


#12 Re: MSI GF63 MS-16W21 - Brak obrazu na LCD, HDMI działa


von martiv 31 März 2025, 13:50
I don't know how it happened, why did I enter it like that? - I presentthe measurement of the drops on the EDP connector

4 - 0.77V - PDM_CLK_CONN
11 - 0V (empty pin in the diagram )
14 - 0.85V (EDP_BKLTCTL)
15 - 1..4V (BL_ON)

I replaced the PU21 chip and as a precaution I did a PCH reflow - No voltage BL_ON

#13 Re: MSI GF63 MS-16W21 - Brak obrazu na LCD, HDMI działa


von matic 31 März 2025, 14:04
martiv hat geschrieben:11 - 0V (empty pin in the diagram )
According to the BoardView I have, this pin is not empty:
Bild
Moreover, if this pin were not used, the voltage drop reading must be OL (Over Load or Out of Range), and not 0V.

#14 Re: MSI GF63 MS-16W21 - Brak obrazu na LCD, HDMI działa


von martiv 31 März 2025, 14:39
the signal is from the KBC kb9548qf2 BGA chip, shouldn't it be 3V?

Re: MSI GF63 MS-16W21 - Brak obrazu na LCD, HDMI działa


von Google Adsense [BOT] 31 März 2025, 14:39

Wer ist online?

Mitglieder in diesem Forum: 0 Mitglieder und 8 Gäste

_______________________________
Alle Rechte vorbehalten. Das unerlaubte Kopieren des Inhalts dieser Website oder eines Teils davon ist strengstens untersagt.
Alle auf dieser Website veröffentlichten Marken, Markennamen, Produkte oder Dienstleistungen gehören ihren gesetzlichen Eigentümern, sind urheberrechtlich geschützt und werden nur zu Informationszwecken verwendet.