• Philips DCM5090/10 - brak reakcji

It is currently 5 January 2025, 22:03

Philips DCM5090/10 - brak reakcji

 Forum rules: Click here to view the forum rules

  1. Topic title should contain: the device's manufacturer, full model and the brief description of problem.
  2. Topic message should contain: the PCB marking code (required in case of hardware repairs), an extended description of problem, things you have checked/replaced/measured, your conclusions and the question. If you are not able to find the PCB marking code, please read THIS TOPIC. If you still cannot locate the PCB markings, please upload a clean, both-side photos of the mainboard - it is required to remove any films, modules or brackets possibly covering these markings.
  3. Before posting a new topic please read all topics in TRAININGS subforum and make a preliminary diagnostic based on the content of those trainings.
  4. Uploading of any complete schematics, BIOS / firmware files or any other kind of documentation, or linking to 3rd party websites with such files, is STRICTLY PROHIBITED. You can only upload the small portion of documentation or, link to BIOS file on UNVERIFIED BIOS FILES subforum, which simplifies the diagnostics/repair. You are not allowed to upload more then one complete page of instruction/schematic per single topic. The file you upload must not contain any watermarks, "confidential" markings, links or email addresses and cannot be password-protected.
  5. It is only permitted to describe one faulty device per single topic - you should always open a new topic for each subsequent device.
  6. Requesting of the full schematics, BoardView files, BIOS files or any other kind of documentation is NOT ALLOWED in this subforum. If you need to ask for any of these, you should open a new topic in DOCUMENTATION/BIOS REQUEST subforum.
 This topic is marked as ARCHIVAL. Please only reply if your message contains the solution (Terms and Conditions p. 12.1).

#1 Philips DCM5090/10 - brak reakcji

by dernis • 4 December 2021, 10:45
witam,

Wieża jak w tytule.. Podczas słuchania muzyki podobno przestała działać..

Wyświetlacz nie reaguje, nie wyświetla żadnej tresci.. świeci tylko niebieska dioda..

Pomiary jakie wykonałem:

CN103:
1- 4,85V
3,4 - 0V
5,6 - 0V
7 - 0V
9 - 0V
10 - 4,6V

IC 401 - 3,3V
IC 402 - 1,8V
IC 403 - 0,49V
IC 404 - 0V

Na włącznik w panelu przychodzi 3,3V i sciagane jest do masy po wciśnięciu ale nie ma żadnej reakcji. Może ktoś pomoże.. schemat jest dostępny ale nie wiem kiedy mają się pojawić napięcia których nie ma...

Re: Philips DCM5090/10 - brak reakcji

by Google Adsense [BOT] • 4 December 2021, 10:45

#2 Re: Philips DCM5090/10 - brak reakcji

by matic • 4 December 2021, 12:44
dernis wrote:Na włącznik w panelu przychodzi 3,3V i sciagane jest do masy
Hello!
On which board the power button is located?

Measure the voltages to ground on pins 1, 9, 10, 11, 12, 15, 16, 20, 34, 35, 61, 69, 71, 72, 86, 87, 96, 100, 102, 103, 108, 110, 113, 114, 115, 116, 117, 118, 120, 121, 122, 123, 126, 127 of µP chip IC101.

#3 Re: Philips DCM5090/10 - brak reakcji

by dernis • 4 December 2021, 14:44
On front panel (VFD & KEY & LED BOARD)

Image

1 -3,3V
9 - 3,3V
10 - 0V
11 -3,3V
12 - 3,3V
15 - 3,3V
16 - 0V
20 - 1,8V
34 - 3,3V
35 - 3,3V
61 - 3,3V
69 - 2,7V
71 - 1,1V
72 - 1,0V
86 - 3,3V
87 - 1,1V
96 - 0,1V
100 -2,1V
102 - 1,8V
103 - 3,6V
108 - 3,3V
110 - 1,8V
113 - 3,3V
114 - 2,7V
115 - 3,3V
116 - 3,3V
117 - 3,3V
118 - 3,3V
120 - 1,3V
121 - 1,6V
122 - 0,1V
123 - 2,1V
126 - 2,0V
127 - 2,8V

#4 Re: Philips DCM5090/10 - brak reakcji

by matic • 4 December 2021, 16:22
Measure the voltages to ground on pins 68, 76, 105 of µP chip IC101 in the following cases:
a) Before pressing to the power button.
b) After pressing to the power button.
c) Power button pressed.

#5 Re: Philips DCM5090/10 - brak reakcji

by dernis • 5 December 2021, 13:33
OK...

is this value correct???
IC 101:
pin 100 - 2,1V (USB_3,3V)

a) Before pressing to the power button:
68 - 3,3V
76 - 0V
105 - 3,3V

b) After pressing to the power button:
68 - 3,3V
76 - 0V
105 - 3,3V

c) Power button pressed.
68 - 0,7V
76 - 0V
105 - 0,2V

#6 Re: Philips DCM5090/10 - brak reakcji

by matic • 11 December 2021, 12:51
dernis wrote:is this value correct???
IC 101:
pin 100 - 2,1V (USB_3,3V)
I think it should be 0V, when the device is turned off and around 3V, when the device is turned on.

Remove the resistor R151 from the board and remeasure the voltages to ground on pins 69, 100 of µP chip IC101.

Re: Philips DCM5090/10 - brak reakcji

by Google Adsense [BOT] • 11 December 2021, 12:51
 This topic is marked as ARCHIVAL. Please only reply if your message contains the solution (Terms and Conditions p. 12.1).
Similar Topics
Acer E5-574G (DA0ZRWMB6G0 REV:G) - brak reakcji, brak 3/5V
  MSI GV72 MS-16j91 VER: 1.0 brak reakcji, brak SUS_ON  [SOLVED]
Brak zasilania BIOS (i brak reakcji) Gigabyte Brix GB-BPCE-3350C
  Lenovo P52 - brak reakcji na przycisk  [SOLVED]
  Xbox Series X - brak reakcji na włącznik  [SOLVED]
  Martwy LG Gram 14Z90P - brak reakcji

Who is online

Users browsing this forum: No registered users and 0 guests

_______________________________
All rights reserved. Unauthorised copying of this website's content or any of its part is strictly forbidden.
Any trademarks, brand names, products or services published on this website belong to their legal owners, are copyrighted and used for information purposes only.