• monitor LG W1953TE no power , no led standby

It is currently 9 January 2025, 17:22

monitor LG W1953TE no power , no led standby

 Forum rules: Click here to view the forum rules

  1. Topic title should contain: the device's manufacturer, full model and the brief description of problem.
  2. Topic message should contain: the PCB marking code (required in case of hardware repairs), an extended description of problem, things you have checked/replaced/measured, your conclusions and the question. If you are not able to find the PCB marking code, please read THIS TOPIC. If you still cannot locate the PCB markings, please upload a clean, both-side photos of the mainboard - it is required to remove any films, modules or brackets possibly covering these markings.
  3. Before posting a new topic please read all topics in TRAININGS subforum and make a preliminary diagnostic based on the content of those trainings.
  4. Uploading of any complete schematics, BIOS / firmware files or any other kind of documentation, or linking to 3rd party websites with such files, is STRICTLY PROHIBITED. You can only upload the small portion of documentation or, link to BIOS file on UNVERIFIED BIOS FILES subforum, which simplifies the diagnostics/repair. You are not allowed to upload more then one complete page of instruction/schematic per single topic. The file you upload must not contain any watermarks, "confidential" markings, links or email addresses and cannot be password-protected.
  5. It is only permitted to describe one faulty device per single topic - you should always open a new topic for each subsequent device.
  6. Requesting of the full schematics, BoardView files, BIOS files or any other kind of documentation is NOT ALLOWED in this subforum. If you need to ask for any of these, you should open a new topic in DOCUMENTATION/BIOS REQUEST subforum.

#1 monitor LG W1953TE no power , no led standby

by eletmoraes • 22 May 2017, 22:53
voltage 12 and 5v --> OK
voltage 3.3v --> OK
Voltage on pin 3 of the UC601 (APE8839) of 5v when it should be 1.8v , located on the video card

Was rewritten the flash memory 25x20 without success. There is another memory located near the connector that goes to the front panel insert that I can not find the firmware to try to re-record. This memory is a 25C02 .
You would have to find the two firmware of this monitor to try to record these two memories.

Re: monitor LG W1953TE no power , no led standby

by Google Adsense [BOT] • 22 May 2017, 22:53

#2 Re: monitor LG W1953TE no power , no led standby

by matic • 23 May 2017, 20:47
Hello!

If the voltage on pin 3 of APE8839 is 5V that chip is probably burned. Yes, it should be 1.8V.
It is bad all other chips on 1.8V power supply line for sure.

#3 Re: monitor LG W1953TE no power , no led standby

by eletmoraes • 24 May 2017, 00:45
Hello, how are you . Before , measured the voltage on pin 3 of the APE8839mp and was supplying 5v, now after removing this component and testing it out and seeing that it is good I ended up soldering the APE8839mp on the video card. When I turned on the monitor, I measured the voltage on the same pin 3 of the APE8839, to my surprise the measured voltage was 1.8V.
Seeing that the basic and main voltages are correct the monitor still does not turn on.
:frustry:




It may be that have some cold solder in this integrated supplying this wrong voltage. What is important now is that the voltages in this component are correct.

#4 Re: monitor LG W1953TE no power , no led standby

by matic • 25 May 2017, 19:00
If you get 3.3V on pin one, and 1.8V on pin three of APE8839 this chip is good.

Measure the voltage on power button.

#5 Re: monitor LG W1953TE no power , no led standby

by eletmoraes • 26 May 2017, 13:46
Sorry friend, this monitor has no on-off button and yes touch, it connects with a finger touch.

#6 Re: monitor LG W1953TE no power , no led standby

by eletmoraes • 11 July 2017, 14:01
I was analyzing the video card better and compared to the monitor scheme, I found two smd resistors that
, Whether it exists or not. It would be the resistor R744 and R745 that on the board they do not contain them and, in the schematic, it is written as "Ready".


R744 ->? Does he exist or not?
R745 ->? Does he exist or not?

#7 Re: monitor LG W1953TE no power , no led standby

by eletmoraes • 12 October 2017, 15:30
As the monitor owner was in a hurry of monitor , I had no choice but to replace the video card. After replacing the video card, the monitor returned to normal operation.

Re: monitor LG W1953TE no power , no led standby

by Google Adsense [BOT] • 12 October 2017, 15:30
Similar Topics
PS4 Power Supply (ADP-240AR AA) - standby voltage is present, missing 12V
  Monitor 65" IIyama TE6502MIS (płyta tp.t972.470w) - brak reakcji na power
  Samsung Led TV UE48JU6410U / stanby led in loop on/off, and won't turn on (Solved)  [SOLVED]
Subwoofer JBL SUB125 - nie uruchamia się, ciągle świeci dioda "standby"
Monitor Iiyama prolite XB24b3hsu-b2 identyfikacja elementu
Monitor Fujitsu KD02902-6132 - zmiana komunikacji z PoweredUSB 12V na USB 2.0 A

Who is online

Users browsing this forum: No registered users and 1 guest

_______________________________
All rights reserved. Unauthorised copying of this website's content or any of its part is strictly forbidden.
Any trademarks, brand names, products or services published on this website belong to their legal owners, are copyrighted and used for information purposes only.