• DELL OptiPlex 3050 startuje tylko po resecie CMOS

It is currently 14 December 2024, 12:27

DELL OptiPlex 3050 startuje tylko po resecie CMOS

 Forum rules: Click here to view the forum rules

  1. Topic title should contain: the device's manufacturer, full model and the brief description of problem.
  2. Topic message should contain: the PCB marking code (required in case of hardware repairs), an extended description of problem, things you have checked/replaced/measured, your conclusions and the question. If you are not able to find the PCB marking code, please read THIS TOPIC. If you still cannot locate the PCB markings, please upload a clean, both-side photos of the mainboard - it is required to remove any films, modules or brackets possibly covering these markings.
  3. Before posting a new topic please read all topics in TRAININGS subforum and make a preliminary diagnostic based on the content of those trainings.
  4. Uploading of any complete schematics, BIOS / firmware files or any other kind of documentation, or linking to 3rd party websites with such files, is STRICTLY PROHIBITED. You can only upload the small portion of documentation or, link to BIOS file on UNVERIFIED BIOS FILES subforum, which simplifies the diagnostics/repair. You are not allowed to upload more then one complete page of instruction/schematic per single topic. The file you upload must not contain any watermarks, "confidential" markings, links or email addresses and cannot be password-protected.
  5. It is only permitted to describe one faulty device per single topic - you should always open a new topic for each subsequent device.
  6. Requesting of the full schematics, BoardView files, BIOS files or any other kind of documentation is NOT ALLOWED in this subforum. If you need to ask for any of these, you should open a new topic in DOCUMENTATION/BIOS REQUEST subforum.
 This topic is marked as ARCHIVAL. Please only reply if your message contains the solution (Terms and Conditions p. 12.1).

#1 DELL OptiPlex 3050 startuje tylko po resecie CMOS

by kwinto10 • 22 April 2022, 14:05
Witam
Płyta VJ40T Rev. A00
W kompie uszkodzone gniazdo USB 3.0 na front panelu. Komputer po resecie startuje, można wejść do bios. Po restarcie brak obrazu, dodatkowo komputer uruchamia się samoczynnie po podaniu zasilania i nie można go wyłączyć tzn przytrzymanie przycisku powoduje wyłączenie i ponowny start.
Po wylutowaniu uszkodzonego gniazda USB przestały działać również tylne porty.
To normalne że brak fizycznie gniazda powoduje wyłączenie wszystkich ?
Porty USB 2.0 też nie działąją nie mam klawiatury ani myszki. Nadal brak obrazu po kolejnym włączeniu.

Re: DELL OptiPlex 3050 startuje tylko po resecie CMOS

by Google Adsense [BOT] • 22 April 2022, 14:05

#2 Re: DELL OptiPlex 3050 startuje tylko po resecie CMOS

by matic • 22 April 2022, 15:02
Hello!

Set your multimeter to the diode test mode and measure the voltage drops to ground on data lines of all USB ports (pins 2, 3 of USB 2.0 ports, pins 2, 3, 5, 6, 8, 9 of USB 3.0 ports).
Image

Re: DELL OptiPlex 3050 startuje tylko po resecie CMOS

by Google Adsense [BOT] • 22 April 2022, 15:02
 This topic is marked as ARCHIVAL. Please only reply if your message contains the solution (Terms and Conditions p. 12.1).
Similar Topics
Dell Latitude 5285 - uruchamia się tylko na zasilaczu, nie startuje na baterii
Dell Latitude e7450 po flashowaniu BIOSu włączył się tylko raz
  [BIOS DUMP REQUEST] DELL AIO OPTIPLEX 7470 IPCFL-GL, i7-9700, MX25L25673GMI
[BIOS DUMP] Dell OptiPlex 7460, MB: Pegatron IPCFL-GL, Rev: A00, UMA wersja
Lenovo Legion 5 17ACH6 NM-D601 Rev 1.0 startuje tylko dioda
Dell Inspiron 5570 LA-F115P rozpoznaje tylko zasilacz 240W.

Who is online

Users browsing this forum: No registered users and 0 guests

_______________________________
All rights reserved. Unauthorised copying of this website's content or any of its part is strictly forbidden.
Any trademarks, brand names, products or services published on this website belong to their legal owners, are copyrighted and used for information purposes only.
cron