plenrusldeituk
  • Inel NUC 8i7BEH Martwy

Forum rules:Click here to view the forum rules

  1. Topic title should contain: the device's manufacturer, full model and the brief description of problem.
  2. Topic message should contain: the PCB marking code (required in case of hardware repairs), an extended description of problem, things you have checked/replaced/measured, your conclusions and the question. If you are not able to find the PCB marking code, please read THIS TOPIC. If you still cannot locate the PCB markings, please upload a clean, both-side photos of the mainboard - it is required to remove any films, modules or brackets possibly covering these markings.
  3. Before posting a new topic please read all topics in TRAININGS subforum and make a preliminary diagnostic based on the content of those trainings.
  4. Uploading of any complete schematics, BIOS / firmware files or any other kind of documentation, or linking to 3rd party websites with such files, is STRICTLY PROHIBITED. You can only upload the small portion of documentation or, link to BIOS file on UNVERIFIED BIOS FILES subforum, which simplifies the diagnostics/repair. You are not allowed to upload more then one complete page of instruction/schematic per single topic. The file you upload must not contain any watermarks, "confidential" markings, links or email addresses and cannot be password-protected.
  5. It is only permitted to describe one faulty device per single topic - you should always open a new topic for each subsequent device.
  6. Requesting of the full schematics, BoardView files, BIOS files or any other kind of documentation is NOT ALLOWED in this subforum. If you need to ask for any of these, you should open a new topic in DOCUMENTATION/BIOS REQUEST subforum.
This topic is marked as ARCHIVAL. Please only reply if your message contains the solution (Terms and Conditions p. 12.1).

#21 Re: Inel NUC 8i7BEH Martwy


by matic 27 July 2023, 12:57
Measure the resistance and voltage to ground on coil "1R5" located near this chip.

Re: Re: Inel NUC 8i7BEH Martwy


by Google Adsense [BOT] 27 July 2023, 12:57

#22 Re: Inel NUC 8i7BEH Martwy


by mmike 27 July 2023, 13:12
1.8 kOhm / 0V

#23 Re: Inel NUC 8i7BEH Martwy


by matic 27 July 2023, 15:16
Replace the marked chip. It's NB680GD.
matic wrote:[ Obrazek ]


#24 Re: Inel NUC 8i7BEH Martwy


by mmike 28 July 2023, 09:27
Myślisz że NB681GD będzie zamienny?
NB680GD jest niedostępny w Polsce... :cry:

#25 Re: Inel NUC 8i7BEH Martwy


by matic 28 July 2023, 09:54
mmike wrote:Myślisz że NB681GD będzie zamienny?
No, there is no replacement for this chip almost for sure.
It appears on some laptop boards, for example: Inventec 6050A2723701-MB-xxx, 6050A2740001-MB-xxx, 6050A2860101-MB-xxx

#26 Re: Inel NUC 8i7BEH Martwy


by mmike 31 July 2023, 09:58
Mam takie modele:

6050A2723701
6050a2892401
6050a2635701

Masz może dokumentacje aby zweryfikować czy posiadają NB680GD ??

#27 Re: Inel NUC 8i7BEH Martwy


by matic 3 August 2023, 14:56
mmike wrote:Mam takie modele:
6050A2723701
Yes, the chip you are looking for should be on this board.
It should be the chip U60100 located in the marked place. Check the markings on the chip itself to make sure. If the markings are ALVx, the chip is suitable.
Image

#28 Re: Inel NUC 8i7BEH Martwy


by mmike 22 August 2023, 08:56
Ukłąd wymieniony na nowy (NB680GD). Nic nie uległo zmianie

Cewka 1R5 - 1.8 kOhm / 0V

#29 Re: Inel NUC 8i7BEH Martwy


by mmike 25 August 2023, 07:30
Jakieś pomysły jeszcze?

#30 Re: Inel NUC 8i7BEH Martwy


by matic 25 August 2023, 08:22
Remeasure the voltages to ground on pins 1, 3, 5, 6, 8, 9, 11 of this chip.
Pin count:
Image

#31 Re: Inel NUC 8i7BEH Martwy


by mmike 25 August 2023, 08:35
1 - 19V
3 - 0V
5 - 0V
6 - 3.3V
8 - 3.2V
9 - 3.6V
11 - 4.1V

#32 Re: Inel NUC 8i7BEH Martwy


by matic 25 August 2023, 13:08
Measure the resistance between pin 5 and pin 7 of this chip.

#33 Re: Inel NUC 8i7BEH Martwy


by mmike 25 August 2023, 13:54
0.1Ohm

#34 Re: Inel NUC 8i7BEH Martwy


by matic 26 August 2023, 19:36
Remove the marked coil from the board and inject 3.3V from the laboratory power supply to the marked pad. Limit the current to 0.5A.
What electrical current flows from the laboratory power supply in this case?
Image

#35 Re: Inel NUC 8i7BEH Martwy


by mmike 28 August 2023, 08:54
22mA

#36 Re: Inel NUC 8i7BEH Martwy


by mmike 31 August 2023, 09:57
Masz jeszcze jakiś pomysł?

#37 Re: Inel NUC 8i7BEH Martwy


by matic 31 August 2023, 10:34
Test the replacement chip NB680GD on your scrap board:
mmike wrote:Mam takie modele:
6050A2723701
Solder the chip to the marked position, inject 19V from the laboratory power supply to the main power rail (B+) and measure the voltages suggested in post #30.
Image

#38 Re: Inel NUC 8i7BEH Martwy


by mmike 31 August 2023, 10:49
Nie ma takiej możliwości płyta złomowa jest zalana.

#39 Re: Inel NUC 8i7BEH Martwy


by matic 31 August 2023, 10:57
Maybe you can clean it.
Is it spilled in the area of this chip?

#40 Re: Inel NUC 8i7BEH Martwy


by mmike 31 August 2023, 10:59
Tak dokładnie płyta jest zalana w tym obszarze, ponadto brak w niej wiele elementów i posiada inne usterki taki pomiar nie będzie miarodajny....

Re: Inel NUC 8i7BEH Martwy


by Google Adsense [BOT] 31 August 2023, 10:59
This topic is marked as ARCHIVAL. Please only reply if your message contains the solution (Terms and Conditions p. 12.1).

Who is online

Users browsing this forum: No registered users and 0 guests

_______________________________
All rights reserved. Unauthorised copying of this website's content or any of its part is strictly forbidden.
Any trademarks, brand names, products or services published on this website belong to their legal owners, are copyrighted and used for information purposes only.