Forum rules: Click here to view the forum rules
- Topic title should contain: the device's manufacturer, full model and the brief description of problem.
- Topic message should contain: the PCB marking code (required in case of hardware repairs), an extended description of problem, things you have checked/replaced/measured, your conclusions and the question. If you are not able to find the PCB marking code, please read THIS TOPIC. If you still cannot locate the PCB markings, please upload a clean, both-side photos of the mainboard - it is required to remove any films, modules or brackets possibly covering these markings.
- Before posting a new topic please read all topics in TRAININGS subforum and make a preliminary diagnostic based on the content of those trainings.
- Uploading of any complete schematics, BIOS / firmware files or any other kind of documentation, or linking to 3rd party websites with such files, is STRICTLY PROHIBITED. You can only upload the small portion of documentation or, link to BIOS file on UNVERIFIED BIOS FILES subforum, which simplifies the diagnostics/repair. You are not allowed to upload more then one complete page of instruction/schematic per single topic. The file you upload must not contain any watermarks, "confidential" markings, links or email addresses and cannot be password-protected.
- It is only permitted to describe one faulty device per single topic - you should always open a new topic for each subsequent device.
- Requesting of the full schematics, BoardView files, BIOS files or any other kind of documentation is NOT ALLOWED in this subforum. If you need to ask for any of these, you should open a new topic in DOCUMENTATION/BIOS REQUEST subforum.
This topic is marked as ARCHIVAL. Please only reply if your message contains the solution (Terms and Conditions p. 12.1).
Re: Samsung np350v QCLA4 LA-8861P - brak napięcia na Vcc kości bios
by Google Adsense [BOT] • 8 August 2024, 17:08
#2 Re: Samsung np350v QCLA4 LA-8861P - brak napięcia na Vcc kości bios
by matic • 9 August 2024, 07:20
Hello!
To enable the +3VS voltage, the signal "SUSP#" should be at high state. This signal is issued by the KBC chip on pin 116. This signal opens the transistor Q6A and consequently pulls the "SUSP" signal to low state. Because the "SUSP" signal is at low state, the transistor Q10A is closed and the power transistor Q29 is opened by the output voltage from the voltage divider formed by resistors R409 and R412.
So, first check if you get a high state (3.3V) on pin 116 of KBC chip after pressing to the power button.
To enable the +3VS voltage, the signal "SUSP#" should be at high state. This signal is issued by the KBC chip on pin 116. This signal opens the transistor Q6A and consequently pulls the "SUSP" signal to low state. Because the "SUSP" signal is at low state, the transistor Q10A is closed and the power transistor Q29 is opened by the output voltage from the voltage divider formed by resistors R409 and R412.
So, first check if you get a high state (3.3V) on pin 116 of KBC chip after pressing to the power button.
#4 Re: Samsung np350v QCLA4 LA-8861P - brak napięcia na Vcc kości bios
by matic • 12 August 2024, 07:20
Measure the voltages to ground on pins 37, 67, 101, 110, 112, 115, 124 of KBC chip.
Measure the voltages to ground on pins 106, 114 of KBC chip in the following cases:
a) Power button released.
b) Power button pressed.
Now disconnect the power supply, wait abut two minutes, reconnect the power supply and perform the following measurements:
Measure the voltages to ground on pins 6, 13, 14, 95, 100, 107, 116, 127 of KBC chip in the following cases:
c) Before pressing to the power button (machine turned off).
d) After pressing to the power button (power LED is turned on).
Measure the voltages to ground on pins 106, 114 of KBC chip in the following cases:
a) Power button released.
b) Power button pressed.
Now disconnect the power supply, wait abut two minutes, reconnect the power supply and perform the following measurements:
Measure the voltages to ground on pins 6, 13, 14, 95, 100, 107, 116, 127 of KBC chip in the following cases:
c) Before pressing to the power button (machine turned off).
d) After pressing to the power button (power LED is turned on).
#7 Re: Samsung np350v QCLA4 LA-8861P - brak napięcia na Vcc kości bios
by Yamaiko • 13 August 2024, 09:37
Okazuje się, że układ UCL1 jest uszkodzony. Brak sygnału o częstotliwości 25Mhz na nóżce 9 powoduje że laptop się nie uruchamia. Odlutowałem kondensator na nóżce 14 i laptop ożył. Zmierzyłem ten kondensator i ma 25uF a powinien mieć według schematu 2.2uF. Możliwe, że przez pojemność układ UCL1 pracuje niestabilnie ?
#8 Re: Samsung np350v QCLA4 LA-8861P - brak napięcia na Vcc kości bios
by carrneiro • 13 August 2024, 15:11
Yamaiko wrote:Okazuje się, że układ UCL1 jest uszkodzony. Brak sygnału o częstotliwości 25Mhz na nóżce 9 powoduje że laptop się nie uruchamia. Odlutowałem kondensator na nóżce 14 i laptop ożył. Zmierzyłem ten kondensator i ma 25uF a powinien mieć według schematu 2.2uF. Możliwe, że przez pojemność układ UCL1 pracuje niestabilnie ?
Jakim cudem 10 krotnie powiększyła mu się pojemność?
Zmierz po wylutowaniu.
#11 Re: Samsung np350v QCLA4 LA-8861P - brak napięcia na Vcc kości bios
by matic • 14 August 2024, 07:52
Yamaiko wrote:Zmierzyłem ten kondensator i ma 25uF a powinien mieć według schematu 2.2uF.The capacitor connected to pin 14 of chip UCL1 is CCL7. Its value according to the schematic is 22µF (not 2.2µF).
Yamaiko wrote:Możliwe, że przez pojemność układ UCL1 pracuje niestabilnie ?Yes, the designer of this board slightly exaggerated the value of these capacitors, which are at the limit of the chip's performance.
For the permanent fix, replace the chip UCL1 and also replace both larger capacitors next to it with their half value:
C16 -> 4.7µF/6.3V, package 0603
CCL7 -> 10µF/6.3V, package 0805
Re: Samsung np350v QCLA4 LA-8861P - brak napięcia na Vcc kości bios
by Google Adsense [BOT] • 14 August 2024, 07:52
This topic is marked as ARCHIVAL. Please only reply if your message contains the solution (Terms and Conditions p. 12.1).
Who is online
Users browsing this forum: No registered users and 2 guests
_______________________________All rights reserved. Unauthorised copying of this website's content or any of its part is strictly forbidden.
Any trademarks, brand names, products or services published on this website belong to their legal owners, are copyrighted and used for information purposes only.