• Samsung UE43TU8005K enters protection after changing the LED strips

It is currently 14 December 2024, 07:00

 [SOLVED] Samsung UE43TU8005K enters protection after changing the LED strips

 Forum rules: Click here to view the forum rules

  1. Topic title should contain: the device's manufacturer, full model and the brief description of problem.
  2. Topic message should contain: the PCB marking code (required in case of hardware repairs), an extended description of problem, things you have checked/replaced/measured, your conclusions and the question. If you are not able to find the PCB marking code, please read THIS TOPIC. If you still cannot locate the PCB markings, please upload a clean, both-side photos of the mainboard - it is required to remove any films, modules or brackets possibly covering these markings.
  3. Before posting a new topic please read all topics in TRAININGS subforum and make a preliminary diagnostic based on the content of those trainings.
  4. Uploading of any complete schematics, BIOS / firmware files or any other kind of documentation, or linking to 3rd party websites with such files, is STRICTLY PROHIBITED. You can only upload the small portion of documentation or, link to BIOS file on UNVERIFIED BIOS FILES subforum, which simplifies the diagnostics/repair. You are not allowed to upload more then one complete page of instruction/schematic per single topic. The file you upload must not contain any watermarks, "confidential" markings, links or email addresses and cannot be password-protected.
  5. It is only permitted to describe one faulty device per single topic - you should always open a new topic for each subsequent device.
  6. Requesting of the full schematics, BoardView files, BIOS files or any other kind of documentation is NOT ALLOWED in this subforum. If you need to ask for any of these, you should open a new topic in DOCUMENTATION/BIOS REQUEST subforum.

#1 Samsung UE43TU8005K enters protection after changing the LED strips

by Zemog • 5 December 2024, 11:23
I have the Samsung UE43TU8005K TV which came with a backlight fault (everything worked fine but it couldn't be seen) and after checking, it had a LED strip in bad condition.
All the LED strips have been dismantled and replaced with new ones.
After the change, when plugging in the TV for a second the LEDs flash intensely and the TV protects itself and turns off. It's as if I was putting more voltage or current into the LED strips.
The new strips are tested and work correctly.
If I turn on the TV without the LED strips connected, it turns on without problems but it can't be seen logically because there is no lighting.
If I turn on the TV without connecting the power supply to the MAIN so that the strips stay permanently on, it causes the intense flash fault and turns off.
The power supply is the Model L43S6_TDY (BN44-01053A) and the backlight controller is MAP3621.
How can I regulate it?

Image

Image

Image

Re: Samsung UE43TU8005K enters protection after changing the LED strips

by Google Adsense [BOT] • 5 December 2024, 11:23

#2 Re: Samsung UE43TU8005K enters protection after changing the LED strips

by matic • 7 December 2024, 19:09
Hello!

Please, post a picture of the old (original) and new LED strips you installed.

#3 Re: Samsung UE43TU8005K enters protection after changing the LED strips

by Zemog • 11 December 2024, 12:01
Image

Image

Image

Image

Image

#4 Re: Samsung UE43TU8005K enters protection after changing the LED strips  [SOLVED] 

by matic • 12 December 2024, 08:06
Test the old and new LED strips with a backlight LED tester. Check, if the tester shows the same forward voltage in both cases.
Image

#5 Re: Samsung UE43TU8005K enters protection after changing the LED strips

by Zemog • 12 December 2024, 14:14
All the new strips were tested with the LED tester before being assembled, and they all had the same voltage 27V, just like the only old LED strip that was in good condition.

Anyway, I went to check them again, and I found a small mark in the connector area. I connected the LED strips and a spark came out from bad contact between the connector and the LED strip.
Since they are new, I have directly changed them for another one from another batch and this one will be returned to the seller.
Thank you very much for your help. Problem solved and TV working

Re: Samsung UE43TU8005K enters protection after changing the LED strips

by Google Adsense [BOT] • 12 December 2024, 14:14
Similar Topics
  Samsung Led TV UE48JU6410U / stanby led in loop on/off, and won't turn on (Solved)  [SOLVED]
Dell Latitude 5580 led blink 1 white 2 orange
Asus MAXIMUS XII APEX r1.01BX RED LED DOES NOT TURN ON
[BIOS DUMP] Samsung NP-RC710, MB: Samsung Jinmao-L, Rev: 1.0, Czysty ME-region
SAMSUNG SM-J530F/DS
  Samsung R522 BA41-01062a problem z biosem  [SOLVED]

Who is online

Users browsing this forum: No registered users and 1 guest

_______________________________
All rights reserved. Unauthorised copying of this website's content or any of its part is strictly forbidden.
Any trademarks, brand names, products or services published on this website belong to their legal owners, are copyrighted and used for information purposes only.