• Lenovo V15-IGL NM-D201 GV452/GV552 Turn on the power LED and nothing else

Forumsregeln:Die Forumsregeln lesen

  1. Der Titel des Themas sollte Folgendes enthalten: den Hersteller der Maschine, das vollständige Modell und die kurze Beschreibung des Fehlers.
  2. Die Themennachricht sollte enthalten: einen PCB-Markierungscode (im Falle von Hardware-Reparaturen), erweiterte Beschreibung des Fehlers, Was wurde überprüft/ersetzt/gemessen + Schlussfolgerungen und, die Frage. Wenn Sie keinen PCB-Markierungscode finden können, du solltest lesen DIESES THEMA. Wenn Sie immer noch keine PCB-Markierungscode finden können, laden Sie bitte ein sauberen Fotos von beiden Seiten des Motherboards - ist es erforderlich, alle Filme und Module zu entfernen, die möglicherweise diese Markierungen abdecken könnte.
  3. Bevor Sie ein neues Thema veröffentlichen, sollten Sie alle Themen im Unterforum AUSBILDUNGEN lesen und machen Sie eine vorläufige Diagnose basierend auf dem Inhalt dieser Ausbildungen.
  4. Das Hochladen vollständiger Anweisungen/Schaltpläne oder BIOS-Dateien / Firmware (oder das Verlinken auf andere Websites mit solchen Dateien) ist STRENG VERBOTEN. Sie können nur den kleinen Teil der Anweisung/Schaltplans oder den Link zur BIOS-Datei in UNVERIFIZIERTE BIOS-DATEIEN platzieren, der die Diagnose und Reparatur für den Themenautor vereinfacht. Sie können nicht mehr als eine vollständige Seite mit Anweisungen/Schaltplänen pro einzelnem Thema platzieren. Die Datei darf keine sichtbaren Wasserzeichen, "vertraulichen" Markierungen, E-Mail-Adressen usw. enthalten.
  5. Pro Thema darf nur eine fehlerhafte Maschine beschrieben werden. Für jede nächste Maschine sollten Sie ein neues Thema öffnen.
  6. Das Anfordern von Schaltplänen, Boardview, MB-Fotos, BIOS-Dateien oder Servicehandbüchern ist STRENG VERBOTEN. Wenn Sie irgendwelche von denen fragen wollen, sollten Sie ein neues Thema in DOKUMENTATION UND BIOS/EFI ANFRAGE Sub-Forum öffnen.

#1 Lenovo V15-IGL NM-D201 GV452/GV552 Turn on the power LED and nothing else


von Zemog 21 Februar 2025, 17:29
Hello everyone!
I have a Lenovo V15-IGL with NM-D201 GV452/GV552 motherboard, which when connecting the power supply, only the Power Led turns on and does nothing else.
With the motherboard removed, without battery and nothing connected (only motherboard), when connecting the power supply the consumption is 50mA.
I have measured the voltages in the coils and all the voltages are correct and present, except PL6601 (+CPU_CORE), where the value is 0V. I have measured the resistance with respect to ground: 40 Ω

I have measured the following voltages on PU6601:
Pin 7 (VCC)... 5V
Pin 11 (VSYS) ... 13,95V
Pin 52 (VIN_CT) ... 19,80V
Pin 16 (SYSON) ... 3,34V
Pin 15 (SUSP#) ... 3,34V
Pin 36 (ALW_PGOOD) ... 3,35V
Pin 27 (SYS_PWROK) .... 3,35V
Pin 45 (+VNN) ... 1,05V
Pin 24, 37 (+1,05VS) ...1,05V
Pin 26, 28 (+1,8VALW) ... 1,8V
Pin 18,21 (+1,2VALW) ... 1,2V
Pin 20 (Gate_VIN) ... 3,35V
Pin 19 (Gate VOUT) .... 2,48V
Pin 3 (+VTT) ... 0,59V
Is the value of pin 3 (+VTT) correct?

On UE1 I have measured the following pins:
Pin 11 (VCC)... 3,34V
Pin 26,50,92,114, 121 (+3VL_EC) ... 3,3V
Pin 74 (+3VL_EC_R) .... 3,3V
Pin 97 (EC_RSMRST#) ... 3,34V
Pin 82 (SYS_PWROK) ... 3,35V
Pin 98 (ALW_PGOOD) ... 3,36V

I initially extracted the SPI Bios (UC2) to make a backup copy, but during the reading, it gave me an error. The programmer recognizes the chip, but every time I try to read it, it gives an error.
I have changed it for a new one, and the new chip, when recording the dump, at the end has given me an error on 2 occasions. The third time it was recorded correctly. After soldering everything remains the same.

Re: Lenovo V15-IGL NM-D201 GV452/GV552 Turn on the power LED and nothing else


von Google Adsense [BOT] 21 Februar 2025, 17:29

#2 Re: Lenovo V15-IGL NM-D201 GV452/GV552 Turn on the power LED and nothing else


von matic 24 Februar 2025, 07:50
Zemog hat geschrieben:The programmer recognizes the chip, but every time I try to read it, it gives an error.
Hello!
Which programmer do you use?

#3 Re: Lenovo V15-IGL NM-D201 GV452/GV552 Turn on the power LED and nothing else


von Zemog 24 Februar 2025, 12:11
matic hat geschrieben:Which programmer do you use?


TL866 II PLUS

EDIT: I have tested the programmer on another computer and I was able to read the BIOS without any problems.
I am going to program a new Dump from this new computer and I will test if there are any changes.

#4 Re: Lenovo V15-IGL NM-D201 GV452/GV552 Turn on the power LED and nothing else


von tekort 24 Februar 2025, 12:50
I have the exact one with the same problem. I also had problems with this chip, mostly during "Verify" phase on SVOD. After programming the BIOS, despite verifying failing, the chip was programmed correctly and the device works. The DMI section for this model is 483000 to 484FFFF.

#5 Re: Lenovo V15-IGL NM-D201 GV452/GV552 Turn on the power LED and nothing else


von Zemog 24 Februar 2025, 13:43
tekort hat geschrieben:The DMI section for this model is 483000 to 484FFFF


Do I have to copy the data from that section, from the backup to the new dump?

#6 Re: Lenovo V15-IGL NM-D201 GV452/GV552 Turn on the power LED and nothing else


von tekort 24 Februar 2025, 14:15
If you want to keep the original serial number you should copy this section from original one to the new dump. It is not mandatory, because device will work without it but in BIOS and in any Lenovo software the serial numbers will have a "INVALID" note.

#7 Re: Lenovo V15-IGL NM-D201 GV452/GV552 Turn on the power LED and nothing else


von Zemog 24 Februar 2025, 17:42
Ok. Thanks a lot for the info, it's very useful for me

After reprogramming I have re-soldered the BIOS, but the problem remains the same. When I connect the power, the power led turns on automatically, and the consumption goes up to 50 mA.
If I keep the power button pressed (which is located on the keyboard), the power led turns off, but the consumption remains at 50 mA. As soon as I release the power button, the power led turns on again with the same consumption
Any suggestions?

#8 Re: Lenovo V15-IGL NM-D201 GV452/GV552 Turn on the power LED and nothing else


von matic 24 Februar 2025, 21:09
Based on the symptoms you described, the communication between the KBC chip and PCH part (small core) of the APU hybrid is almost certainly missing.
Unfortunately, the APU hybrid is very likely damaged.

Wer ist online?

Mitglieder in diesem Forum: Google [Bot] und 5 Gäste

_______________________________
Alle Rechte vorbehalten. Das unerlaubte Kopieren des Inhalts dieser Website oder eines Teils davon ist strengstens untersagt.
Alle auf dieser Website veröffentlichten Marken, Markennamen, Produkte oder Dienstleistungen gehören ihren gesetzlichen Eigentümern, sind urheberrechtlich geschützt und werden nur zu Informationszwecken verwendet.