• Acer Nitro 5 AN-515 LA-H501P Martwy

Forumsregeln:Die Forumsregeln lesen

  1. Der Titel des Themas sollte Folgendes enthalten: den Hersteller der Maschine, das vollständige Modell und die kurze Beschreibung des Fehlers.
  2. Die Themennachricht sollte enthalten: einen PCB-Markierungscode (im Falle von Hardware-Reparaturen), erweiterte Beschreibung des Fehlers, Was wurde überprüft/ersetzt/gemessen + Schlussfolgerungen und, die Frage. Wenn Sie keinen PCB-Markierungscode finden können, du solltest lesen DIESES THEMA. Wenn Sie immer noch keine PCB-Markierungscode finden können, laden Sie bitte ein sauberen Fotos von beiden Seiten des Motherboards - ist es erforderlich, alle Filme und Module zu entfernen, die möglicherweise diese Markierungen abdecken könnte.
  3. Bevor Sie ein neues Thema veröffentlichen, sollten Sie alle Themen im Unterforum AUSBILDUNGEN lesen und machen Sie eine vorläufige Diagnose basierend auf dem Inhalt dieser Ausbildungen.
  4. Das Hochladen vollständiger Anweisungen/Schaltpläne oder BIOS-Dateien / Firmware (oder das Verlinken auf andere Websites mit solchen Dateien) ist STRENG VERBOTEN. Sie können nur den kleinen Teil der Anweisung/Schaltplans oder den Link zur BIOS-Datei in UNVERIFIZIERTE BIOS-DATEIEN platzieren, der die Diagnose und Reparatur für den Themenautor vereinfacht. Sie können nicht mehr als eine vollständige Seite mit Anweisungen/Schaltplänen pro einzelnem Thema platzieren. Die Datei darf keine sichtbaren Wasserzeichen, "vertraulichen" Markierungen, E-Mail-Adressen usw. enthalten.
  5. Pro Thema darf nur eine fehlerhafte Maschine beschrieben werden. Für jede nächste Maschine sollten Sie ein neues Thema öffnen.
  6. Das Anfordern von Schaltplänen, Boardview, MB-Fotos, BIOS-Dateien oder Servicehandbüchern ist STRENG VERBOTEN. Wenn Sie irgendwelche von denen fragen wollen, sollten Sie ein neues Thema in DOKUMENTATION UND BIOS/EFI ANFRAGE Sub-Forum öffnen.

#21 Re: Acer Nitro 5 AN-515 LA-H501P Martwy


von psikus123 6 März 2025, 13:54
Po usunięciu PU502 napięcia na PR504 się nie zmieniły.
PR504
0,069V
3,17V
Sprawdziłem poza płytą PR507 jest 1MOhm

Re: Re: Acer Nitro 5 AN-515 LA-H501P Martwy


von Google Adsense [BOT] 6 März 2025, 13:54

#22 Re: Acer Nitro 5 AN-515 LA-H501P Martwy


von matic 6 März 2025, 15:38
Please, post clear pictures of the marked area from both sides of the board (no need to solder the removed chip back to the board for now).
Bild

#23 Re: Acer Nitro 5 AN-515 LA-H501P Martwy


von psikus123 6 März 2025, 15:45
Bild
Bild

#24 Re: Acer Nitro 5 AN-515 LA-H501P Martwy


von matic 6 März 2025, 20:37
Sorry, but your pictures are not clear at all and are more or less useless for further diagnostics.
We are interested in a quality sharp picture of the marked area with clearly visible copper traces and vias on the board.
By the way, it's not necessary to post a picture of 1/4 of the entire board, we are only interested in the 5x5cm area, as marked with a yellow rectangle in post #22.

#25 Re: Acer Nitro 5 AN-515 LA-H501P Martwy


von psikus123 7 März 2025, 08:55
Te zdjęcia powinny być dobre.
Bild
Bild
Bild
Zrobiłem modyfikację jak na ostatnim zdjęciu.
PU502 - nie zamontowany
Po podłączeniu zasilania na pin 12 PU502 pojawiło się 3,3V
Czy mogę montować PU502 i próbować uruchamianie płyty?

#26 Re: Acer Nitro 5 AN-515 LA-H501P Martwy


von matic 7 März 2025, 10:04
These pictures are better.

It seems there is a short circuit between the layers somewhere inside the PCB board.
Cut the copper trace on the board as shown in the picture below and remeasure the voltages to ground on both pins of resistor PR504. The board is multi-layer, so be careful to not cut too deep (cut the top copper layer only).
Bild

#27 Re: Acer Nitro 5 AN-515 LA-H501P Martwy


von psikus123 7 März 2025, 10:06
W momencie Twojej odpowiedzi wyedytowałem post wyżej - spójrz.

#28 Re: Acer Nitro 5 AN-515 LA-H501P Martwy


von matic 7 März 2025, 11:26
psikus123 hat geschrieben:Po podłączeniu zasilania na pin 12 PU502 pojawiło się 3,3V
I didn't noticed that the resistor PR505 is also present on the board (it's actually a copper trace on the PCB).
So that means something is wrong with the signal line "MAINPWON". It pulls the line "5V_3V_EN" to the low state).

psikus123 hat geschrieben:Czy mogę montować PU502 i próbować uruchamianie płyty?
Yes, you can, but the board will not work as the signal "MAINPWON" is interrupted now.

- Restore the cut copper trace - you can solder a 0Ω resistor to the place of PR505.
- Remove the transistor Q1 from the board and check if 3V is still present on pin 12 of chip PU502.

#29 Re: Acer Nitro 5 AN-515 LA-H501P Martwy


von psikus123 7 März 2025, 11:53
Wcześniej z przeciętą ścieżką PR505 zamontowałem PU512 i na cewce PL501 było 5V.

Odbudowałem ścieżkę PR505 Usunąłem Q1 i na pin 12 PU502 jest 0,070V

jak podniosłem 104 nogę KBC to na PU512 pokazało się 3,3V.
Wadliwy KBC?

#30 Re: Acer Nitro 5 AN-515 LA-H501P Martwy


von matic 7 März 2025, 13:33
psikus123 hat geschrieben:Wadliwy KBC?
Yes, possible.
First try to reflash the KBC chip with programmer. If it doesn't change anything, replace the KBC chip.

#31 Re: Acer Nitro 5 AN-515 LA-H501P Martwy


von psikus123 10 März 2025, 09:08
KBC programowałem 4 wsadami, które zdobyłem z forów także elvikom.
Wymieniłem KBC 2 razy, pierwszy z partii, które kiedyś kupiłem z Chin oraz znalazłem na płycie co mam na części, wszystkie programują się i weryfikują pozytywnie.
Myślę, że problem KBC jest wykluczony , na każdym wsadzie i KBC na pin 12 PU512 jest 0,07V.
Sprawdziłem wszystkie elementy na linii MAINPWON profilaktycznie wymieniłem DB1.
Gdzie szukać dalej?

#32 Re: Acer Nitro 5 AN-515 LA-H501P Martwy  [GELÖST]


von matic 10 März 2025, 09:57
Check, if 5V on the coil PL501 appears and disappears instantly at plugging the power supply to the board.

#33 Re: Acer Nitro 5 AN-515 LA-H501P Martwy


von psikus123 10 März 2025, 10:10
Nie, nie pojawia się żadne napięcie nawet chwilowe na PL501 natychmiast po podłączeniu zasilania

Przyczyną okazał się utleniony pad pod PH201, jego wymiana przywróciła laptopa do normalnej pracy.
Dziękuję matic za poświęcony czas.

Re: Acer Nitro 5 AN-515 LA-H501P Martwy


von Google Adsense [BOT] 10 März 2025, 10:10

Wer ist online?

Mitglieder in diesem Forum: 0 Mitglieder und 8 Gäste

_______________________________
Alle Rechte vorbehalten. Das unerlaubte Kopieren des Inhalts dieser Website oder eines Teils davon ist strengstens untersagt.
Alle auf dieser Website veröffentlichten Marken, Markennamen, Produkte oder Dienstleistungen gehören ihren gesetzlichen Eigentümern, sind urheberrechtlich geschützt und werden nur zu Informationszwecken verwendet.