• problem with changing board in samsung syncmaster S20v310b plus

It is currently 8 January 2025, 12:01

problem with changing board in samsung syncmaster S20v310b plus

 Forum rules: Click here to view the forum rules

  1. Topic title should contain: the device's manufacturer, full model and the brief description of problem.
  2. Topic message should contain: the PCB marking code (required in case of hardware repairs), an extended description of problem, things you have checked/replaced/measured, your conclusions and the question. If you are not able to find the PCB marking code, please read THIS TOPIC. If you still cannot locate the PCB markings, please upload a clean, both-side photos of the mainboard - it is required to remove any films, modules or brackets possibly covering these markings.
  3. Before posting a new topic please read all topics in TRAININGS subforum and make a preliminary diagnostic based on the content of those trainings.
  4. Uploading of any complete schematics, BIOS / firmware files or any other kind of documentation, or linking to 3rd party websites with such files, is STRICTLY PROHIBITED. You can only upload the small portion of documentation or, link to BIOS file on UNVERIFIED BIOS FILES subforum, which simplifies the diagnostics/repair. You are not allowed to upload more then one complete page of instruction/schematic per single topic. The file you upload must not contain any watermarks, "confidential" markings, links or email addresses and cannot be password-protected.
  5. It is only permitted to describe one faulty device per single topic - you should always open a new topic for each subsequent device.
  6. Requesting of the full schematics, BoardView files, BIOS files or any other kind of documentation is NOT ALLOWED in this subforum. If you need to ask for any of these, you should open a new topic in DOCUMENTATION/BIOS REQUEST subforum.
 This topic is marked as ARCHIVAL. Please only reply if your message contains the solution (Terms and Conditions p. 12.1).

#1 problem with changing board in samsung syncmaster S20v310b plus

by Amir • 6 December 2017, 08:25
hi to all
in samsung S20v310b plus after changing mainboard(damaged) i have a problem.blanking backlight.i have no signal logo without problem.
model code:ls20v300bschd (back cover label)
main board old: sa300/sa350 bn41-01592d rev no:mp 1.0 (20 inch)
new main board:sa300/sa350 bn41-01592b rev no:mp 1.0 ( 19 inch)
panel spec:LTM200KT08
i tested with several flash dump but just blinking backlight problem .
with some file no blinking but character is out of size.
please help me.
tn

Re: problem with changing board in samsung syncmaster S20v310b plus

by Google Adsense [BOT] • 6 December 2017, 08:25

#2 Re: problem with changing board in samsung syncmaster S20v310b plus

by matic • 6 December 2017, 21:15
Hello!

Try to transplant old FLASH chip to the new board (if the old FLASH chip is not broken).

#3 Re: problem with changing board in samsung syncmaster S20v310b plus

by Amir • 7 December 2017, 17:28
tnx matic
one of my friend had problem like this.
he changed 19 inch backlight with 20 inch backlight and problem solved.
may chang backlight wiring to solve problem?
Image

Image

#4 Re: problem with changing board in samsung syncmaster S20v310b plus

by matic • 7 December 2017, 19:48
If so, the issue could be with LED backlight driver circuit, which can not handle with less LED strips in backlight. The 20 inch display is larger than 19 inch, so there are more LED-s inside.

Post clear pictures (with visible component markings) of the following part of the old and new board.

Image

#5 Re: problem with changing board in samsung syncmaster S20v310b plus

by Amir • 8 December 2017, 15:19
hi
all the part is the same . i checked Carefully.
I have to say with 22 inch firmware no blinking and backlight worked fine but the all font size is out of range.
it is wiring problem or firmware problem?

#6 Re: problem with changing board in samsung syncmaster S20v310b plus

by matic • 8 December 2017, 15:43
If all of the components in the backlight driver circuit have the same value like on the old board (specially a current sensing resistors R828, R829, R831, R832, R833 and inductors L801 and L802) the issue is probably a firmware, which is not compatible with that type of LCD panel.

As I said before:
matic wrote:Try to transplant old FLASH chip to the new board (if the old FLASH chip is not broken).


#7 Re: problem with changing board in samsung syncmaster S20v310b plus

by Amir • 8 December 2017, 15:57
tnx matic
i missed old firmware .

Re: problem with changing board in samsung syncmaster S20v310b plus

by Google Adsense [BOT] • 8 December 2017, 15:57
 This topic is marked as ARCHIVAL. Please only reply if your message contains the solution (Terms and Conditions p. 12.1).
Similar Topics
  Samsung UE43TU8005K enters protection after changing the LED strips  [SOLVED]
MacBook Air M3, A3113, EMC 8611, Mobo 661-40169, Keyboard Connection Board Problem
  Samsung R522 BA41-01062a problem z biosem  [SOLVED]
[BIOS DUMP REQUEST] ASUS ZenBook Flip UX463FL (UX334FL MAIN BOARD REV. 2.0)
Asus K55VJ Laptop (K55VM 2.2 PWR BOARD) prośba o identyfikację elementu.
  Hp 840 G3 board no: 6050A2822301-MB-A01 /burnt component  [SOLVED]

Who is online

Users browsing this forum: No registered users and 0 guests

_______________________________
All rights reserved. Unauthorised copying of this website's content or any of its part is strictly forbidden.
Any trademarks, brand names, products or services published on this website belong to their legal owners, are copyrighted and used for information purposes only.